C150 series cable mounted

Coupler

C150 series cable mounted

Design: cable mounted coupler (plug & receptacle)
Contact assignment: 3 phase, 1 ground, 1 pilot
Rated voltage: 15 kV 3 AC
Rated withstand voltage: 50 kV (1 min) dry
Rated current: 500 A
Short circuit current: 38 kA RMS
Frequency: 50 – 60 Hz
Protection class: IP 67H
Ambient temperature: -40 °C to +45 °C
Shock resistance: IK 10
Sealing: EPDM and potting compound
Cable cross section / ø: 35 – 240 mm² / 21 – 89 mm
Material: sea water resistant aluminum
Surface treatment: nature, epoxy powder coating
Dimensions P / R (L x H): 622 x 267 mm / 686 x 292 mm
Weight Plug / Receptacle: 17 kg / 17 kg
USP: with separable fiber optic connection (optionally)

C-Coupler-Series

  • Fiber optic components have been developed to meet military specifications and requirements
  • Three times the crush resistance and twice the tensile strength of non-metallic fiber optic cables
  • Communication is not impacted even if rolled over by a tank
  • Totally rodent proof
  • Pollution resistance – designed for connection and disconnection on site
  • High performance 2,5 mm termini and a split ceramic alignment sleeve assures superior performance and low optical insertion loss even under high shock and vibration
  • Aluminum enclosure with durable anodization
  • Stainless steel version on request
  • APC terminals on request
  • Single mode and multi mode operation possible
  • Configurable design supports from 2 -18 fiber channels per connector
  • Environmental sealing to IP68
Product: Live current insulated cover
Features: Possibility of applying a voltage to the connector even when not plugged in
Design: Male design for C80D1-series
Female design for C80D2-series
Mating combability: for 5, 8 and 15 kV coupler of C series
Rated voltage Male / Female Pluggable with Patton & Cooke
250 A M PK8S-Mxy PK8F-Mx C80C1000x 11E-073
F RK8S-Fxy RK8F-Fx C80C2000x 11E-073A
400 A M PL5S-Mxy PL5F-Mx 11D-110
C80D1000x C80D3008
F RL5S-Fxy RL5F-Fx 11D-110A
C80D2000x C80D3009
Product: short circuit cover
Features:
  • for shorting and grounding
  • avoidance of capacitive loads
  • in the cable and connectors
Design: plug design for C80D1-series
receptacle Design for C80D2-series
Usage: for C80D-series (400 A)
  • The strain relief entrance fittings are included with the couplers C10, C80, C150, CEM150, C250 and P/R series. For the IMG series both, the original IMG and P&C entrance fittings can be used => depending on cable
  • The entrance fitting gasket kits are normally not included with the C coupler series. For Europe, there are exceptions, so this point must be requested on a case by case basis. The same applies to the IMG series.
  • The termination kits must be ordered separately with the C80, C150, CEM150 and P/R series. However no termination kits are required for the C250 coupler and the whole IMG series.
  • Potting compound is recommended for the C80 and the P/R series but required for the C150 and CEM150. For the C250 and the whole IMG series no potting compound is required but possible as an additional sealing against the formation of moisture

The termination kit for preparing the conductors consists of: emery paper, shrink tubing, adhesive strap, copper contact tape, contact spring, resin for pressure relief and solvent as well as cleaning cloths.

Sketch Outer cable diameter Article number
(mm) (in)
21 – 47 0.820 – 1.870 C150F3029
48 – 60 1.880 – 2.370 C150F3030
61 – 69 2.380 – 2.750 C150F3031
70 – 89 2.760 – 3.500 C150F3032
Suitable for C80, C150, CEM 150 and C250 connector and coupler series
Cable diameter Article number
(mm) (in)
20,8 – 22,1 0.82 – 0.87 C150F3004
22,4 – 23,9 0.88 – 0.94 C150F3005
24,1 – 25,7 0.95 – 1.01 C150F3006
25,9 – 26,9 1.02 – 1.06 C150F3007
27,2 – 28,4 1.07 – 1.12 C150F3008
28,7 – 31,8 1.13 – 1.25 C150F3009
32,0 – 34,8 1.26 – 1.37 C150F3010
35,0 – 38,1 1.38 – 1.50 C150F3011
38,4 – 41,1 1.51 – 1.62 C150F3012
41,4 – 44,5 1.63 – 1.75 C150F3013
44,7 – 47,5 1.76 – 1.87 C150F3014
47,8 – 50,8 1.88 – 2.00 C150F3015
Cable diameter Article number
(mm) (in)
51,1 – 53.8 2.01 – 2.12 C150F3016
54,1 – 57,2 2.13 – 2.25 C150F3017
57,4 – 60,2 2.26 – 2.37 C150F3018
60,5 – 63,5 2.38 – 2.50 C150F3019
63,8 – 66,5 2.51 – 2.62 C150F3020
66,8 – 69,9 2.63 – 2.75 C150F3021
70,1 – 72,9 2.76 – 2.87 C150F3022
73,2 – 76,2 2.88 – 3.00 C150F3023
76,5 – 79,2 3.01 – 3.12 C150F3024
79,5 – 82,6 3.13 – 3.25 C150F3025
82,8 – 85,6 3.26 – 3.37 C150F3026
85,9 – 88,9 3.38 – 3.50 C150F3027
Suitable for C80, C150, CEM150 and C250 coupler series
Pay attention: The sealing inserts normally must be ordered separately!